Most manufacturers allow the fireplace to sit directly on a combustible floor. A combustible platform can also be built at this time to raise the unit within the wall opening if you wish. Pay close attention to any side clearances or overhead ceiling clearances outlined by the manufacturer. It's at this time that the consideration for finishing material thickness should also be made.
Whatever the thickness of the material, you must ensure the unit projects forward from the framed opening enough to compensate for the thickness of the finishing material if you are looking for a flush installation.
This will ensure that the tile will be relatively flush with the face of the unit when finishing is completed. Some manufacturers provide nailing tabs that will be at different depths on the appliance to help compensate for the setback you need. If the tabs don't provide enough projection, the unit may need to be shimmed as you install it.
Check to make sure the unit is plumb and level before nailing it into position. Cedar shims can be used to make adjustments if needed. Other designs use similar caps or lids for the unused flue collar, while a few designs are a dedicated top or rear vent configuration. The installation of the venting components should come next.
Almost all gas vent pipes will use a twist lock attachment method. Depending on how you are venting the appliance, you may need to uncover or rotate the venting collar on the appliance for your application. For instance, Superior direct vent gas appliances will have the vertical flue collar covered by a plate and the back collar covered by a cap. If you are venting the appliance vertically, you'll need to remove the plate and discard the insulation and pipe plug within.
If venting horizontally, the rear cap would need to be removed in the same fashion. Once the vent collar has been configured properly, the first piece of pipe can be installed. Before attaching to the appliance, a bead of a direct vent appliance sealant should be applied to the inner pipe wall.
Ensure that the dimples on each pipe align with the channels on the flue collar, and firmly twist the pipe clockwise until it ceases to rotate. Double-check the connection by pulling upward on the pipe. If any dimple pulls loose, the connection was not correctly made and should be attempted again. The screws should only be allowed to penetrate the outer wall of the pipe.
Continue your installation with each section of vent pipe , repeating the twist, check, and screw method for the entirety of the run. Check the pipe run to ensure that you are maintaining the minimum required clearances to combustibles at all times. It's recommended to secure the pipe run every 5 feet by wrapping the pipe with perforated HVAC strapping and securing the strapping to adjacent studs. This will limit the amount of lateral motion in the pipe run.
Most manufacturers will also provide a sheet metal firestop that should be installed at the ceiling level. The firestop can be installed once the ceiling level has been reached. It's common practice to install 2 x 4 lumber immediately adjacent to both sides of the pipe to give the firestop plate something to nail to.
Some jurisdictions will also require that you enclose the top of your framed fireplace enclosure with a plywood or oriented strand board. If this is the case, the plywood or strand board must be cut to the dimensions of your enclosure and nailed into place atop 2 x 4 scabbing. Depending on your preference, the vent pipe can be exposed above the roof or boxed into a decorative chimney chase.
If left exposed, a roof flashing will be used to seal the termination. The image above depicts a venting run that has penetrated a wooden firestop and uses metal strapping to support an offset in the pipe run. The vent pipe can be exposed above the roof or boxed into a decorative chimney chase. As the pipe installation nears the roof decking, a plumb bob or level can be used to determine the point of penetration.
Using a reciprocating or jigsaw, cut a hole large enough in the roof to ensure the pipe can pass through and meet all applicable clearances. It should be noted that the steeper the roof is, the longer the hole parallel to the roof slope will be.
Installation of the flashing will follow the normal procedure for all roof flashing, with the leading edge of the flashing tucked under the uppermost row of shingles, the adjacent shingles lapped over the flashing edges and the trailing edge of the flashing atop the shingles. As you affix and run the last section of the pipe through the flashing, the storm collar should be attached around the pipe and also sealed. The cap should be installed last and screwed into position as with the previous pipe sections.
Wood burning appliances follow much of the same design and installation requirements as gas appliances, but there are some differences. Upon completion of the venting installation, the electrical and plumbing that has been previously installed by a local professional can be connected to the appliance.
If your appliance required electrical service for the ignition system or circulating fan, there will be a supplied junction box installed inside the unit. This will be outlined in the wiring diagram within the owner's manual. Following the diagram, connect the wire leads of the new circuit to the wire pigtails supplied with the unit.
Each connection should be made using a NEMA approved wire nut and electrical tape. Most units will usually provide an anti-strain fitting that will be used to secure the wiring connection.
Any loose wire from the circuit should be secured with NEMA approved wire staples. The gas connection to the unit should be made with an approved flex connector and fittings. Teflon pipe tape or pipe thread sealant should be made at all connections, save for the flex line connections. If there are any doubts about one's abilities for the electrical and plumbing connections, a licensed professional should be consulted.
Wood burning appliances follow much of the same design and installation requirements as a gas appliance, but there are some differences. Wood burning fireplaces will always be vertically vented and won't require the use of any sealant at the flue collar connection.
They will also not require an electrical or plumbing connection in most cases. The installation of a circulating fan or a gas starting aid would be exceptions to this rule. Because of the potential for extremely high temperature, wood burning chimneys are also much larger in diameter and will sometimes require additional clearances to combustibles.
These are lightweight fireplaces often with linear designs to fit more modern tastes. In comparison with masonry fireplaces, they're easier to install and require significantly less construction work.
Since their firebox enclosures always remain cool, zero-clearance fireplaces can be installed in any room—even directly over hardwood floors and within a few inches of existing walls.
If you want to get the most use out of your fireplace , plan to put the new fireplace in the most-used room in the house other than the kitchen, such as the family room or living room. For heating practicality, it makes sense to put it in a smaller, easy-to-heat room such as a master bedroom, office, or spare bedroom.
No matter which room you decide on, make sure its floor joists are reinforced. You should also factor in the dimensions and thickness of the firebox, the size of the damper opening, and the type of chimney and liner used. Refer to your local building codes to get detailed specifications for each of these considerations as well as for the minimum distance between a fireplace and combustive materials. Some building codes require that the house framing be modified to accommodate the increased weight of the fireplace addition.
Everyone loves the comfy look of a fireplace, but not all homes come equipped with the favorite feature. The good news is that it's easy to add a fireplace to an existing home. All it takes is a little know-how. Some Corner Fireplace Mantels are made specifically for electric Inserts. But some manufacturers have designed their fireplaces to work with both types of inserts so you can choose what type of fireplace you want without having to worry about finding a specific corner mantel that will fit your insert.
A Corner Fireplace is typically around inches wide. This leaves plenty of room for a mantel and other decorations. Some Corner Fireplaces are even narrower, so be sure to measure the space you have before purchasing one. There is no need to worry if your living room is on the small side. You can still include a Corner Fireplace without taking up too much space. Just follow these simple tips:.
Fireplace inserts are a great way to add warmth and ambiance to your home without having to install or perform any major renovations. Yes, there is such a thing! There are a few things you need to consider before buying a natural gas Corner Fireplace.
For starters, make sure that your home has the proper ventilation for a fireplace. Finally, be sure to budget for the installation of a natural gas Corner Fireplace. Yes, a stand alone Fireplace can be placed in a Corner. However, you will need to take some measurements and do some planning before you purchase your unit.
Make sure that the unit you choose is small enough to fit comfortably in the corner, but large enough to provide heat for the room. You may also want to consider an electric unit for your corner. One important thing to keep in mind is that if you are placing the unit against an outside wall, there should be at least one foot of clearance on all sides between the Fireplace and any combustible surface. This can pose a problem with tight corners where space is limited.
No, gas Fireplaces should only be installed at 90 degrees to the wall. The opening on a corner is typically too high and creating an unsafe installation. Please contact your local Gas Safe registered installer for further assistance with this question.
Yes, you can put a fireplace in the corner of a room. The key is to make sure that there is enough space on either side of the fireplace for people to comfortably stand and enjoy the fire.
The space should be at least three feet away from the wall and longer if your fireplace is tall. If wood or gas logs are burning in the firebox, then leave an additional three feet behind the fireplace. The size of the insert you need for your Fireplace will depend on the dimensions of your fireplace opening. Most Corner vent gas Fireplaces are around 42 inches tall. This measurement includes the mantel, which is usually around inches tall. You can use the same height measurements above to figure out how much clearance you need in front of your Corner vent gas Fireplace.
The distance between mantel and the corner should be at least two feet for an optimal viewing experience, though three feet is ideal. Three foot wide Corner vent gas Fireplaces are less common than their 42 inch counterparts, so you might have to settle for a slightly smaller model.
If you are considering putting a fireplace in your home, it is important to understand the potential environmental impacts before you make your decision. The Environmental Protection Agency EPA has developed emissions guidelines for wood-burning fireplaces and stoves, which help ensure that these products do not cause adverse health effects.
To learn more about how our fireplace inserts can reduce harmful levels of smoke in your home, please visit our website. Yes, it is possible to do this. In fact, there are many reasons why people would want to have their fireplace surround by corners as opposed to an open space. The main reason is that if the room has one side significantly longer than another side — for example, if it is a long, narrow room — then the fireplace can be placed against the shorter side to create a more balanced look.
Another reason people might want to put their fireplace in a corner is if they have limited space in their home. By placing the fireplace against one of the walls, it will take up less space than if it was placed in the middle of the room. In addition, if you have a large piece of furniture — such as a sofa — that is also taking up space near where your fireplace would normally go, then putting it against one wall will free up some valuable floor space for other pieces of furniture or even an area rug to be placed.
This is a popular question, and the answer really depends on your specific situation. If you have a lot of space above your fireplace, then it might be a good idea to put your television up there so that you can take advantage of that extra real estate.
0コメント