Here you determine the time limit for reception of signals from sensors used to monitor the activity of sick, elderly or disabled people. Options: 3, 6, 12, 24, 48, 72 hours and no act disable.
Note: The Not Active timer is defined for the entire alarm system for the above hour options and not per partition in a PowerMax Pro Partition system. Subsequently, a dedicated timer is assigned to each partition. Here you determine whether the keypad back lighting will remain on at all times or will come on when a key is pressed and go off within 10 seconds if no further keystrokes are sensed. The two options are: always on and off after 10 s.
A duress alarm ambush message can be sent to the central station if the user is forced to disarm the system under violence or menace. To initiate a duress message, the user must disarm the system with the duress code by default. Here you can change the code digits or enter "" to disable the duress feature. The system does not allow the user to program the duress code saved in this memory location as an existing user code.
Here you determine whether the internal siren will sound or remain silent upon alarm according to the user preference. Options: piezo siren on, piezo siren off.
Not applicable in the USA Here you determine whether the system can be rearmed after an event by the user or only by the installer. Options: user reset or engineer reset. If Engineer Reset is selected, the system can be rearmed only by the installer; by entering and exiting the installer menu, by entering and exiting the event log see section 7 , or by remote telephone.
To perform Engineer Reset via the telephone, establish communication with the PowerMax Pro see user guide, par. Wait for 2 beeps c. Here you determine whether zone tamper will be reported or ignored. Here you determine whether the siren will be activated or not when the telephone line fails during system armed state. Available options are: enable on fail, disable on fail. Here you determine whether the user will receive indication that an alarm has been activated. Available options are: enable and disable.
Here you determine when it is possible to disarm the system: A. Any time. Option Fig. Available options are: EN standard and other. Here you determine whether the user will hear or will not hear low battery sound when he tries to disarm the system with a keyfob whose battery voltage is low. Available options are: keyfob L-B on the user has to acknowledge the keyfob low battery message or keyfob L-B off the user does not have to acknowledge the keyfob low battery message.
You can determine that button normal display will return after pressing the followed by entering user code Refresh by Code or after pressing any key Refresh by Key. If Refresh by Key is selected, the first pressing of any key except Fire and Emergency will cause normal display return and the second press will perform the key function.
Options: scrn saver OFF, refresh by code, refresh by key. Here you determine whether or not the system can be armed and disarmed by zones , or , provided that for these zones "non-alarm type" and "z-key enable" was predefined see par. Key zones can be wireless or wired zones. Arming the system using a transmitter assigned to zones 21 and 28, or via wired zones 29 and 30 compromises security. This function is, therefore, only available in specific PowerMax Pro versions according to the customer's request.
Options: disable option, z. Here you determine that if 2 successive alarms will occur during a specific period, the second alarm will be considered as a confirmed alarm for confirmed alarm reporting, see par.
Options: disable 30 min. Here you determine the time interval between AC power failure occurrence and the failure reporting. Options: 5 minutes, 30 minutes, 60 minutes or minutes. Options: Enable, Disable. Note: This menu is not available when partition is enabled. To review the options, repeatedly click or until the desired option is displayed, then click OK a dark box will be displayed at the right side.
In telephone number locations, these digits are used as codes to control the dialer: Hex. Line Prefix [Fig 4. Dial Method [Fig 4. The options are: Pulse and tone dtmf.
The options are: disable and every 28 days. Each of the channels can be separately enabled or disabled in order to allow or prohibit the module from using it for the event reporting.
If fails, it will try GSM Voice. This is due to the fact that SMS is the most unreliable option of communication. Disabling any of the GSM Module channels will cause the module to use a different sequence than the one described above. The options are: disable and enable. GSM Report [Fig 4. SMS Report [Fig 4. Key Functionality Moves the cursor from left to right. Long press for speed.
Moves the cursor from right to left. Scrolls upward the sequence of inserted digits. Scrolls downward the sequence of inserted digits. Places cursor to extreme right position of edit string and shows the last 16 digits of edit string. Reverts to previous or top menu without saving the edit string. Saves and reverts to previous menu. Clears all digits to the right of cursor. Clears one digit by cursor. Selects between uppercase or lowercase digits. Antenna Select [Fig 4.
The options are: Internal Antenna and External Antenna. PIN Code [Fig 4. Force Home Network [Fig 4. The asterisk J is a separator between events reported to central station 1 and events reported to central station 2. Messages are divided by type into four groups: No. The options are: disable, cellular and PSTN. If the method defined to report events in the 1st priority fails, the control panel will attempt to report using the method defined in the 2nd priority see notes in 1st Report Method.
If the method defined to report events in the 2nd priority fails, the control panel will attempt to report using the method defined in the 3rd priority see notes in 1st Report Method. Dual Reporting [Fig 4. Receiver 1 Account No. The number consists of 6 hexadecimal digits. Receiver 2 Account No. The account number consists of 6 hexadecimal digits.
The options are: 10, 20, 33 and 40 pps. The options are: 2, 4, 8, 12 and 16 attempts. Auto Test Time [Fig 4. Auto Test Cycle [Fig 4. The control panel performs this at regular intervals to verify proper communications.
The options are: test every 5 hours, test every 1, 2, 5, 7, 14, 30 days and test OFF. Line Fail Report [Fig 4. If the telephone line is disconnected, the message "tel line fail" will be stored in the event log. The options are: don't report, immediately, 5 minutes, 30 minutes, 60 minutes or minutes.
If the telephone line is disconnected, the message "GSM line fail" will be stored in the event log. The options are: don't report, 2 minutes, 5 minutes, 15 minutes, or 30 minutes. The options are: rem. Downl Code [Fig 4. Upload Option [Fig 4. Note: Only for use with control panels monitored by compatible central stations.
Leave empty if not used. The options are: send and don't send. This option is applicable only after reporting an event to the central station. The central station person can press [3] for listen-in", [1] for "speak out" or [6] for listening and speaking. The options are: 10, 45, 60, 90 seconds, 2 minutes, ring back and disable no two-way voice communication. Ringback Time [Fig 4. Alarm type message was received by central station.
Ring Back function was selected [see par. The options are: 1, 3, 5 or 10 minutes. Ambient Level [Fig 4. If it is a relatively noisy environment, set it to High default setting.
If it is a very quiet environment, set to Low. The options are: low and high. Report Cnfrm Alarm [Fig 4. Report 24H Zones [Fig 4. The options are: both original, audible as panic, silent as panic, or both as panic. Recent Close [Fig 4. Zone restore [Fig 4. The options are: report restore and don't report. System Inactivity Report [Fig 4. The options are: disable, rep. The options are: enable 2-way and disable 2-way.
Note: In the single acknowledge mode, receiving an acknowledge signal from a single telephone is sufficient to consider the current event closed and call off the communication session. The remaining telephones serve for backup purposes only. In the all acknowledge mode, an acknowledge signal must be received from each telephone before the current event is considered reported. The options are: single ack and all ack. Voice report [Fig 4. Redial Attempts [Fig 4. The options are: 1, 2, 3 and 4 attempts.
A maximum of 2 dialing attempts is permitted by the Australian Telecommunication Authority. External anten. To rev iew the options , repeatedly click or until the desired option is displayed, then click OK a dark box will be displayed at the right side. Enter Tel. Enter SIM card Tel. Enter 2nd IP receiver Tel. OFF recent cl. ON Par. To rev iew th e options, repeatedly click or until the desired option is displayed, then click OK a dark box will be displayed at the right side.
GSM modem auto detection is activated in one of two ways: after tamper restore and after reset power-up or after exiting the installer menu. In the event that the GSM modem auto detection fails and the modem was previously enrolled in the PowerMax Pro control panel, the message "Cel Rmvd Cnfrm" will be displayed.
This message will disappear from the display only after the user. The modem is then considered as not clicks enrolled and no GSM trouble message will be displayed. Note: A message is displayed only when the PowerMax Pro alarm system is disarmed.
PowerLink modem auto detection is activated in one of two ways: after tamper restore and after reset power-up or after exiting the installer menu. This message will disappear from the display only. The modem is then after the user clicks considered as not enrolled and no PowerLink trouble message will be displayed. DEIP b. Function type selection for every X unit and PGM output. General definitions selection for X units. Enrolling 2-way X units. Each selected option is displayed with a dark box at the right side.
To review the options, repeatedly click or button, until the desired option is displayed, then click button. If you select toggle, the PGM output will be turned on upon event occurrence in these zones and will be turned off upon next event occurrence, alternately. If strobe is selected, the INT output will be activated when an alarm occurs until the system is disarmed i.
House code selection a code letter from A to P that will distinguish the site in which the system is installed from other sites in the neighborhood. Specific number definition for every X unit 01 — Enrolling 1-way X units d. Enrolling 2-way X units that can perform status reporting. Note: If a 2-way X unit is installed without enrolling, interference to the 1-way X units operation may occur.
If you select toggle, the X output will be turned on upon event occurrence in these zones and will be turned off upon next event occurrence, alternately.
Upon selecting any one of the 3 options zone a, b and c you may enter a zone number and then select "disable", "turn on", "turn off", "pulse active" or "toggle". To review the options, repeatedly click button until the desired option is displayed, then click a dark box will be displayed at the right side.
For zone name list, refer to paragraph 4. In case of event, the relevant user name will be added to the message that will be reported via the telephone. These names are useful if none of the 26 fixed zone names are found suitable for a certain zone see fig.
The recording process is shown below. Living room, Library, etc. The dark square boxes slowly disappear, one by one, until end of recording time. In case of communication failure detailed information is reported. Unit failed with registration to local GSM network. APN is not configured. To unlock it enter a PUK number. The VDNS denies the connection request.
Reliable reception must be assured. Therefore, a "poor" signal strength is not acceptable. If you get a "poor" signal from a certain detector, re-locate it and re-test until a "good" or "strong" signal strength is received. Visonic produces the PowerMax and PowerMaster alarm panel series. The Visonic Powermaster range of alarms does everything Visonic Powermax range of alarms do, but also are designed for remote control, smart phone connectivity and camera sensors.
Figure 5. Support comprenant les piles G. Mettre le support comprenant les piles en place, remonter le cache plastique et visser la vis de fixation. Using the PowerMax Remote Programmer, he can compare the parameters of the different systems and copy them if necessary. The data is then transferred to each PowerMax through a modem. Figure … PowerMax Pro kontrolpanelet leveres med to manualer: Installationsmanual denne manual er alene til dit brug Brugermanual anvendes kun af dig under installationen og skal overlades til hovedbrugeren efter, at systemet er testet.
L This is a professional product and should be installed by a. Before you begin you should know that this kit is supplied with.
Additionally, each transmitter is labelled. Following this. Details on managing and top-. Installations connected to a central monitoring centre.
Make a cup of tea, and spend the next. Choose a Location to Mount your Control Panel. Additionally think. We recommend you test. Then power the panel by connecting. The backup battery may take an hour to reach full capacity,.
0コメント